Letter from Melanie Dawes to owners, landlords and managers of private residential blocks about safety checks following the Grenfell Tower fire

We hope you find our news updates useful. If you know of anyone who may benefit from reading them, please encourage them to register at the bottom-left of our news page (http://www.eljay.co.uk/news/) and we’ll email them a link each time an update is published. If in the unlikely event any difficulties are experienced whilst registering we’ll be more than happy to help and can be contacted on 07896 016380 or at Fiona@eljay.co.uk

Melanie Dawes, Permanent Secretary at the Department of Communities and Local Government (DCLG), has written to owners, landlords and managers of private residential blocks about safety checks following the Grenfell Tower fire. The government is making available testing facilities for private owners of residential blocks that have cladding made of aluminium composite material, and the letter explains how to identify this cladding, and access the testing facilities.

The letter, and supporting documents, can be viewed by clicking on the following link: https://www.gov.uk/government/publications/safety-checks-on-private-residential-blocks and we have published the contents below. Queries should be directed to PRShousingchecks@communities.gsi.gov.uk, but if you require any general assistance regarding fire safety in blocks of flats, please don’t hesitate to contact us on 07896 016380 or at fiona@eljay.co.uk, and we’ll be happy to help.

Safety checks on private residential blocks

This letter is intended for owners, landlords and managers of private residential blocks in England. Representative bodies for the private residential sector have kindly agreed to disseminate this letter to their members, and we are grateful for their assistance.

Following the horrific fire at Grenfell Tower in North Kensington last week, we want to ensure you are aware of help that is available in checking your buildings.

There has been much public concern and comment about potential flaws in the cladding that was on Grenfell Tower. While the exact reasons for the speed of the spread of fire have yet to be determined, we have concluded that there are additional tests that can be undertaken with regard to the cladding. We have asked local authorities and social housing providers to identify whether any panels used in new build or refurbishment of their own housing stock are a particular type of cladding made of Aluminium Composite Material (ACM). These checks will be relevant to privately owned and managed residential buildings too, so please can you consider carrying out these checks on your buildings.

More details on how to identify this cladding are in Annex A below.  It is important to stress that ACM cladding is not of itself dangerous, but it is important that the right type is used. If you identify that cladding on any of your buildings is made of ACM, then a sample can be tested.

This testing facility is also being made available to blocks that are privately owned, and your local authority may already have been in touch to make you aware of this.  The procedures for taking up this offer of testing, which will be paid for by DCLG, are set out in the annex. We are prioritising buildings over six storeys or 18 metres high.  The offer is for the initial testing only and the cost of any remedial action will be the responsibility of the owner of the building. The information from the checks will be available to DCLG from BRE. Please contact us at PRShousingchecks@communities.gsi.gov.uk if you have any queries.

Where the entire block is not owned and managed by the same party, please ensure that only one sample is provided and that any necessary permissions are obtained for taking and sending off the sample. We would not expect individual leaseholders within a building to send off samples for testing.

As well as this work it is of course important that owners / landlords have robust fire assessments for their properties.

Thank you for your cooperation in this important work.

MELANIE DAWES

Annex A

Protocol for Sampling of Aluminium Composite Material Cladding

Identification of Aluminium Composite Material Cladding

Aluminium Composite Material (ACM) is a type of flat panel that consists of two thin aluminium sheets bonded to a non-aluminium core, typically between 3 and 7mm thick. The panels can have a painted or metallic finish (eg copper or zinc effects). It can be differentiated from solid aluminium sheet by looking at a cut edge whereby the lamination is visible. It may be necessary to cut a hole in a panel if a cut edge is not readily accessible.

On buildings with a floor over 18m above ground level, where ACM panels are identified, it is necessary to establish whether the panels are of a type that complies with the Building Regulations guidance ie the core material should be a material of limited combustibility or Class A2.

Testing of ACM

To allow for the identification of core materials, we are putting in place Government-funded testing capacity that will allow a small sample of the cladding to be tested and its type identified. If you wish to take up this offer, then you will need to submit samples for testing.

Where the surveyor undertaking assessment of a composite panel determines that it is necessary for cladding to be subjected to laboratory screening they should follow this procedure:

  1. Cut out two samples of at least 250x250mm in size from each location sampled. Take photographs as necessary to identify the location of the sample. You should take samples from above and below 18m above ground level as appropriate and check different multiple panels where you have concern that material specification varies.
  1. Using an indelible ink pen, note the building name / number, postcode and a unique identifier (i.e. name of building owner followed by unique sample number e.g. ABC/001) traceable to the specific location within the building of each sample. Add a direct dial telephone or mobile contact number to be used in the event that there are any queries on the sample.
  1. You must make good by closing the hole using a non-combustible sheet such as steel fixed with self-tapping screws or rivets.
  1. Complete the data return form attached to this letter (https://www.gov.uk/government/uploads/system/uploads/attachment_data/file/620798/Data_Return_Form_for_testing_of_ACM_-_private_residential.xlsx) and include a hard copy of it with the sample. You should provide as much information as is readily available, but not if this will delay submission of samples for testing.
  1. Place one of the samples from each location in a padded envelope with a copy of the data return form. Clearly mark the envelope URGENT – CLADDING TEST SAMPLE.
  1. Send the test samples by recorded delivery or courier to:

BRE, Bucknalls Lane, Garston, Watford, Herts, WD25 9XX

For any testing related queries please email material.screening@bre.co.uk

  1. Retain the second sample from each location for your own records or for testing in the event that samples are lost or misplaced in transit

Contains public sector information licensed under the Open Government Licence v3.0.

 

Gas boilers – flues in voids (HSE Safety Notice); housing association prosecuted for safety failings

We hope you find our news updates useful. If you know of anyone who may benefit from reading them, please encourage them to register at the bottom-left of our news page (http://www.eljay.co.uk/news/) and we’ll email them a link each time an update is published. If in the unlikely event any difficulties are experienced whilst registering we’ll be more than happy to help and can be contacted on 07896 016380 or at Fiona@eljay.co.uk

Housing association prosecuted for safety failings

A housing association has been prosecuted after allowing renovations to take place that put residents at risk of carbon monoxide poisoning.

A Sheriff Court heard that one of Scotland’s largest registered social landlords had allowed chimneys to be removed from properties on two separate occasions. It was later discovered during the annual gas checks that the chimneys acted as the necessary gas flue for adjacent properties.

HSE’s investigation into both incidents revealed that at the time the chimney removals took place not only was there was no procedure in place for the company’s workers to follow in respect of this type of work, neither were any risk assessments carried out in relation to the chimney removals which would have identified the risk to carbon monoxide poisoning for the residents.

The housing association pleaded guilty to breaching Section 3(1) of the Health and Safety at Work etc Act (1974) and was fined £8,000.

Around seven people die each year from carbon monoxide poisoning caused by gas appliances and flues that have not been properly installed, maintained or that are poorly ventilated.

Gas boilers – flues in voids (updated 20th May 2013)

This Safety Notice provides updated information to that in the safety alert that was issued by the Health and Safety Executive (HSE) on 2nd October 2008 following a death earlier that year.

The purpose of the original Alert was to raise awareness of the potential dangers from certain types of flues connected to gas-fired central heating installations in some properties (particularly, but not exclusively, a large number of flats and apartments completed since about 2000) that may not have been installed properly, or may have fallen into disrepair.

Where boilers are located away from external walls, flues are more likely to run through ceiling (or wall) voids. In such cases when the gas appliance is serviced or maintained it can be difficult, or impossible, to determine whether the flue has been installed correctly or whether it is still in good condition.

Where a flue fault exists in combination with a boiler which is not operating correctly, dangerous levels of carbon monoxide (CO) could be released into the living accommodation. CO is a colourless, odourless, tasteless, poisonous gas produced by incomplete burning of carbon-based fuels. It stops the blood from bringing oxygen to cells, tissues, and organs and can kill quickly, without warning.

The 2008 Alert referred to the relevant gas industry technical guidance which gas engineers were expected to follow. A revised version of this guidance has now been published by Gas Safe Register. This changes the approach that Gas Safe registered engineers will take when they encounter relevant installations.

The purpose of this Safety Notice is to make homeowners, landlords and tenants aware of these changes as action might be required. It is not, however, the only means of communication. An industry working group (including representatives of the gas industry, home builders, home warranty providers and boiler manufacturers, assisted by HSE) will ensure that information is readily available to all those who may be affected.

Background

The introduction of fan-flued gas appliances in the mid 1990s allowed gas central heating boilers to be installed away from external walls. This meant that builders could design new-build and refurbishment properties with boilers being installed on internal walls to make better use of the available space. The flues to these boilers were, in some cases, routed through voids in the ceiling space (and through stud walls) between properties above.

This practice became progressively more popular from 2000 onwards and the vast majority of affected systems are thought to be located in new build flats and apartments completed since 2000. It is however possible that other types of home may have similar central heating systems installed.

Gas engineers are legally required to check the flue after carrying out any work on the boiler. This will include a visual inspection. Similarly, when an engineer installs a boiler they need to ensure that it can be used without constituting a danger to anyone; this would include checking whether the flue is safe. The original installer and every subsequent servicing or maintenance engineer need to be able to check that:

  • the flue is continuous throughout its length;
  • all joints are correctly assembled and are appropriately sealed; and
  • the flue is adequately supported throughout its length.

Unless the gas engineer can make these checks they cannot ensure that the flue from the boiler is safe in order to comply with their legal duties. This necessitates the provision of appropriate inspection hatches in the ceiling (and, where relevant, stud wall).

The original industry technical guidance (aimed at registered gas engineers) advised that where the flue to the boiler was concealed within a void and could not be visually inspected it should be assessed as “not to current standards” (NCS) in accordance with the Gas Industry Unsafe Situations Procedure (GIUSP – see Reference section for explanation). This was dependent on there being no other risks being present which may have made the boiler unsafe.

Revised guidance takes effect on 1st January 2011. This is the result of the industry working group who undertook a review of the original guidance and concluded that the potential risk from such systems, should it not be possible to inspect the flue, requires an alternative approach to ensure that the necessary remedial action is taken.

Action required

The revised technical guidance requires inspection hatches to be fitted in properties where the flue is concealed within voids and cannot be inspected. The homeowner (or landlord etc.) has until 31st December 2012 to arrange for inspection hatches to be installed. Any gas engineer working on affected systems after 1st January 2013 will advise the homeowner that the system is “at risk” (AR) in accordance with the GIUSP and, with the owner’s permission will turn off the gas supply to the boiler so it cannot be used.

In the interim period, where no inspection hatches are fitted, the registered gas engineers will carry out a simple risk assessment which should ensure that the risk from exposure to CO is managed in the short-term. This risk assessment includes:

  • looking for signs of leakage along the flue route; and
  • carrying out a flue combustion analysis check (and obtaining a satisfactory result); and
  • checking for the presence of suitable audible carbon monoxide (CO) alarms (and installing such alarms where they are not already fitted).

As long as this boiler passes the series of safety checks and the risk assessment does not identify any concerns about its safety, it can be left on. Suitable inspection hatches will however need to be fitted to the ceiling (or wall, as appropriate) by end 31st December 2012. Wherever possible it is recommended that inspection hatches are fitted before this date.

Once inspection hatches have been fitted, the gas engineer will be able to make sure that the flue is safe and was installed in line with the relevant standards and manufacturers instructions.

A simple explanation of the issue, the risks and how the matter can be resolved, as well as a number of frequently asked questions, have been developed for householders. The industry working group are looking at how best to target individual households that are most likely to be affected. In the meantime, further information is available on the Gas Safe Register website: http://www.gassaferegister.co.uk/fluesinvoids

If you are unsure whether a property has concealed gas flues and think you might be at risk:

  • If you have your gas appliances checked annually by a Gas Safe registered engineer he/she will be able to advise whether this Notice applies to your property.
  • If you do NOT have your boiler regularly serviced arrange for a Gas Safe registered engineer to visit to check the appliances and flues. Show them this Notice.

If a property has concealed flues in voids and no inspection hatches:

  • If the property is less than 2 years old contact the original builder for assistance with the retrofitting of inspection hatches and repair of any flue defects.
  • If the property is between 2 and 10 years old contact the home warranty provider as you may be covered by them if there are defects in the flue. The main warranty providers (NHBC, Premier Guarantee and Zurich Building Guarantee) have however advised that cover is not provided for installing inspection hatches in homes over two years old.
  • If the property is 10 years or older you should contact a Gas Safe registered engineer. You or your landlord will have to meet the cost of the inspection hatches and any defects to the boiler or its flue. It may still be worth contacting the home builder who may be able to assist in some way, or be able to recommend reputable building services companies to carry out the work.

Having taken advice as above, arrange for a competent builder or building services company to fit inspection hatches as soon as you can and, in any case, by 31st December 2012. (If you don’t, from 1st January 2013 a Gas Safe registered engineer will advise you that the appliance is “at risk” and, with your permission, will turn off the appliance; they will tell you it should not be used until inspection hatches are fitted so that the flue can be checked for safety.)

Do not:

  • Attempt to check the flue system yourself (unless you are a Gas Safe registered engineer). You are likely to do more harm to the installation and place you and your family at greater risk.
  • Try to install inspection hatches yourself. You may damage other key functions of the ceiling, such as fire and noise proofing.

If you live in rented accommodation and think your property might be affected:

  • Bring this Notice to the attention of your landlord or managing agent. It is the responsibility of the landlord to ensure that inspection hatches are installed and that the boiler and flue are checked every year.

If you think you are suffering the symptoms of CO poisoning:

  • Turn the appliance off immediately and contact the National Gas Emergency Service on 0800 111 999.
  • If you think you or your family experience any of the symptoms of CO poisoning you should seek urgent medical advice from either your GP or an accident and emergency department.

For more information visit the HSE web page: http://www.hse.gov.uk/safetybulletins/fluesinvoids.htm or contact us on 07896 016380 or at fiona@eljay.co.uk and we’ll be happy to help.

Contains public sector information published by the Health and Safety Executive and licensed under the Open Government Licence

 

 

Passenger lifts and escalators – Bolton resident dies in lift shaft fall

We hope you find our news updates useful. If you know of anyone who may benefit from reading them, please encourage them to register at the bottom-left of our news page (http://www.eljay.co.uk/news/) and we’ll email them a link each time an update is published. If in the unlikely event any difficulties are experienced whilst registering we’ll be more than happy to help and can be contacted on 07896 016380 or at Fiona@eljay.co.uk

Bolton resident dies in lift shaft fall

A property management company has been fined after a resident of an apartment block in Bolton died after falling down a lift shaft.

Bolton Crown Court heard how the resident and a friend were trapped in a lift and unable to raise the alarm. They attempted a self-rescue by forcing the doors open and sliding out onto the floor below.

The resident slipped under the lift car and fell five stories down the lift shaft and died of multiple injuries. His friend escaped unhurt.

An investigation by the Health and Safety Executive (HSE) into the incident which occurred in August 2014 found that the management company for the building failed to take suitable and sufficient steps to prevent the resident and his friend self-rescuing.

The management company pleaded guilty to breaching Section 3(1) of the Health and Safety at Work etc Act 1974, and was fined £120,000 and ordered to pay costs of £45,000.

Speaking after the hearing HSE inspector Sarah Taylor said: “Those who manage lifts have a responsibility to ensure they are properly maintained but if people are trapped they have a way to raise the alarm and are not in a position to try and rescue themselves.

“The problems with this lift were well known and if [the management company] had fulfilled their health and safety responsibilities [the resident] would probably be around to celebrate Christmas with his family this weekend.”

Passenger lifts and escalators

Lifts provided for use by workers in workplaces are subject to the Lifting Operations and Lifting Equipment Regulations (LOLER). However, in most cases lifting equipment which is not provided for, or used by, people at work (eg stair lifts in private dwellings and platform lifts in shops used for customer access) will not be subject to either LOLER or PUWER. But businesses providing this equipment will have responsibilities for its safety (it will require routine maintenance and inspection).

LOLER does not apply to escalators or any travelators / moving walkways which transport people, even though they may ‘lift’ people from one level to another. Such equipment is covered by regulation 19 of the Workplace (Health, Safety and Welfare) Regulations.

However, escalators and similar machines, platform and stair lifts, and all conventional passenger lifts must meet the requirements for safety and conformity of either the Machinery or Lift Directives in their design, construction and installation, when first brought into use. (Note: stair lifts, certain slow moving platform lifts (less that 0.15 m/s) and construction hoists come within scope of the Machinery Directive instead of the Lifts Directive).

Passenger lifts used by people at work

Passenger lifts and combined goods / passenger lifts in workplaces (eg offices and factories) which are primarily used by people at work, are subject to periodic thorough examination and inspection, as required by LOLER and PUWER. Guidance for lift owners and others responsible for the examination and testing of lifts is available in: Thorough examination and testing of lifts: Simple guidance for lift owners (http://www.hse.gov.uk/pubns/indg339.htm)

Passenger lifts used by people who are not at work

LOLER (and PUWER) may not apply where a passenger lift is not used by people at work (eg in public areas of a shopping centre). However, if the lift is operated by – or to some extent under the control of – an employer or self-employed person in connection with their business, they still have some responsibility for the health and safety of people they don’t employ. This includes members of the public who use the lift and those people who may work on or inspect the lift.

Section 3 of the Health and Safety at Work Act imposes these general responsibilities, so far as reasonably practicable. As the risks may be the same as when using lifts in connection with work, a similar regime of maintenance, inspection and examination to that required under LOLER and PUWER may be entirely ‘reasonably practicable’ in managing the risks. In any case, insurers may impose demands for similarly stringent levels of risk management to cover public liability.

Escalators and moving walkways

Guidelines for the safe operation of escalators and moving walks (walkways) have been prepared by the Safety Assessment Federation in consultation with HSE. This document provides considerable guidance on the duties and responsibilities of those who:

  • manufacture, supply and install escalators and moving walkways
  • design premises where they are to be installed
  • own or manage premises in which they are installed, and
  • inspect and examine escalators and moving walkways

Although not subject to LOLER, these detailed guidelines recommend thorough examination of escalators and moving walkways, normally at six-monthly intervals.

Stair lifts:

Where provided as work equipment for use by employees, stair lifts will be subject to the requirements of LOLER (thorough examination) and PUWER (maintenance and inspection). Where they are not, but are still provided in connection with an undertaking (eg in work environments where the public or visitors may use them), employers and the self-employed will have responsibilities for the safety of all users under Section 3 of the Health & Safety at Work etc Act 1974. These may be adequately discharged by undertaking maintenance, and inspection, and 6 monthly thorough examination, even though PUWER & LOLER may not apply to the equipment.

However, all new stair lifts (either when first placed on the market, or first brought into use), as machinery are subject to the Machinery Directive / Supply of Machinery (Safety) Regulations 2008. They must be constructed to be safe, supplied with Instructions, a Declaration of Conformity and CE marking. Those stair lifts which involve a hazard of falling from a vertical height of 3m or more are subject to Annex IV (item 17) of the Machinery Directive (so subject to conformity assessment as required by Article 12 (3) or 12 (4) of 2006/42/EC).

More information on LOLER can be found on the LOLER FAQ page: http://www.hse.gov.uk/work-equipment-machinery/faq-lifting.htm

For more information visit the HSE web page: http://www.hse.gov.uk/work-equipment-machinery/passenger-lifts.htm or contact us on 07896 016380 or at fiona@eljay.co.uk, and we’ll be happy to help. We carry out health and safety inspections (as well as fire/legionella risk assessments) of all types of residential and commercial properties and are happy to provide a no-obligation quotation on request.

Contains public sector information published by the Health and Safety Executive and licensed under the Open Government Licence

 

 

Need building work done? A short guide for clients (building owners, users or managing agents) on the Construction (Design and Management) Regulations 2015

We hope you find our news updates useful. If you know of anyone who may benefit from reading them, please encourage them to register at the bottom-left of our news page (http://www.eljay.co.uk/news/) and we’ll email them a link each time an update is published. If in the unlikely event any difficulties are experienced whilst registering we’ll be more than happy to help and can be contacted on 07896 016380 or at Fiona@eljay.co.uk

This guidance is aimed at you if you are a building owner, user or managing agent and are having maintenance, small-scale building work or other minor works carried out in connection with a business – as you will be a client with legal duties under the Construction (Design and Management) Regulations 2015 (CDM 2015).

Following the simple steps below will help you meet your responsibilities as a client and ensure construction work and repairs are undertaken safely and without damaging worker’s and other people’s health.

What does CDM 2015 do?

Complying with CDM 2015 will help ensure that no-one is harmed during the work, and that your building is safe to use and maintain while giving you good value. Effective planning will also help ensure that your work is well managed with fewer unexpected costs and problems.

What do clients need to do?

Many clients, particularly those who only occasionally have construction work done, are not experts in construction work. Although you are not expected to actively manage or supervise the work yourself, you have a big influence over the way the work is carried out. Whatever the size of your project, you decide which designer and contractor will carry out the work and how much money, time and resource is available. The decisions you make have an impact on the health, safety and welfare of workers and others affected by the work.

CDM 2015 is not about creating unnecessary and unhelpful processes and paperwork. It is about choosing the right team and helping them to work together to ensure health and safety.

As a client, you need to do the following.

  1. Appoint the right people at the right time

If more than one contractor will be involved, you will need to appoint (in writing) a principal designer and a principal contractor.

A principal designer is required to plan, manage and coordinate the planning and design work.  Appoint them as early as possible so they can help you gather information about the project and ensure that the designers have done all they can to check that it can be built safely.

A principal contractor is required to plan, manage and coordinate the construction work. Appoint them as early as possible so they are involved in discussions with the principal designer about the work.

Getting the right people for the right job means your designers and your contractors need to have the skills, knowledge and experience to identify, reduce and manage health and safety risks. This is also the case if they are a company (known as having ‘organisational capability’ for the job). The designers and the contractors should be able to give references from previous clients for similar work and explain to you how they will achieve this.

Professional bodies can help you choose your architect and other designers. The Safety Schemes in Procurement (SSIP) website has lists of businesses which have been assessed on their health and safety management. A contractor may be a member of a trade association.

  1. Ensure there are arrangements in place for managing and organising the project

The work is more likely to be done without harming anyone and on time if it is properly planned and managed. Sometimes the work is complex and uses many different trades. Often it involves high-risk work such as the work listed in the bulleted list below. The principal designer should understand these types of risks and try to avoid them when designing your project. The principal contractor or builder should manage the risks on site.

These are the biggest causes of accidents and ill health in construction work, and your designer and contractor can manage the risks by doing the following.

Falls from height:

  • Make sure ladders are in good condition, at a 1:4 angle and tied or footed.
  • Prevent people and materials falling from roofs, gable ends, working platforms and open edges using guardrails, midrails and toeboards.
  • Make sure fragile roof surfaces are covered, or secure working platforms with guard rails are used on or below the roof.

Collapse of excavations:

  • Shore excavations; cover or barrier excavations to prevent people or vehicles from falling in.

Collapse of structures:

  • Support structures (such as walls, beams, chimney breasts and roofs) with props; ensure props are installed by a competent person.

Exposure to building dusts:

  • Prevent dust by using wet cutting and vacuum extraction on tools; use a vacuum cleaner rather than sweeping; use a suitable, well-fitting mask.

Exposure to asbestos:

  • Do not start work if it is suspected that asbestos may be present until a demolition/refurbishment survey has been carried out.

Electricity:

  • Turn the electricity supply and other services off before drilling into walls.
  • Do not use excavators or power tools near suspected buried services.

Protect members of the public, the client, and others:

  • Secure the site; net scaffolds and use rubbish chutes.

Discuss with your designer and builder before work starts and throughout the build how these risks are being managed.

  1. Allow adequate time

Work that is rushed is likely to be unsafe and of poor quality. Allow enough time for the design, planning and construction work to be undertaken properly.

  1. Provide information to your designer and contractor

Your designer and builder will need information about what you want built, the site and existing structures or hazards that may be present such as asbestos, overhead cables, and buried services. Providing this information at an early stage will help them to plan, budget and work around problems. Your principal designer can help you gather this information.

Putting together a ‘client brief’ at the earliest stages which includes as much information as you have about the project, along with the timescales and budget for the build and how you expect the project to be managed can help you to set the standards for managing health and safety.

  1. Communicate with your designer and building contractor

Your project will only run efficiently if everyone involved in the work communicates, cooperates and coordinates with each other.

During the design and planning stage, you, your designer and contractor need to discuss issues affecting what will be built, how it will be built, how it will be used and how it will be maintained when finished. This will avoid people being harmed or having unexpected costs because issues were not considered when design changes could still easily be made.

Meeting with your designer and contractor as the work progresses gives an opportunity to deal with problems that may arise and discuss health and safety. This will help to ensure that the work progresses as planned.

  1. Ensure adequate welfare facilities on site

Make sure that your contractor has made arrangements for adequate welfare facilities for their workers before the work starts. See the HSE publication Provision of welfare facilities during construction work (see ‘Further reading’).

  1. Ensure a construction phase plan is in place

The principal contractor (or contractor if there is only one contractor) has to draw up a plan explaining how health and safety risks will be managed. This should be proportionate to the scale of the work and associated risks and you should not allow work to start on site until there is a plan.

  1. Keep the health and safety file

At the end of the build the principal designer should give you a health and safety file. If the principal designer leaves before the end of the project, the principal contractor (or contractor if there is only one contractor) should do this. It is a record of useful information which will help you manage health and safety risks during any future maintenance, repair, construction work or demolition. You should keep the file, make it available to anyone who needs to alter or maintain the building, and update it if circumstances change.

  1. Protecting members of the public, including your employees

If you are an employer, or you have members of the public visiting your premises, you need to be sure that they are protected from the risks of construction work.

Discuss with your designer and contractor how the construction work may affect how you run your business, eg you may have to re-route pedestrian access; make sure signs to your entrance are clear; or change the way your deliveries operate.

  1. Ensure workplaces are designed correctly

If your project is for a new workplace or alterations to an existing workplace (eg a factory or office), it must meet the standards set out in the Workplace (Health, Safety and Welfare) Regulations 1992 (see ‘Further reading’).

Notifying construction projects

For some construction work (work lasting longer than 30 days with more than 20 workers working at the same time, or involving 500 person days of work), you need to notify HSE of the project as soon as possible before construction work starts. In practice, you may request someone else to do this on your behalf.

How can you find out more?

Your principal designer or principal contractor will be able to advise you on your duties.

Why you should comply with your duties as a client

If you do not comply with CDM 2015, you are likely to be failing to influence the management of health and safety on your project. This means that your project could be putting workers and others at risk of harm, and that the finished structure may not achieve good standards and be value for money.

If you don’t appoint a principal designer or principal contractor you will be responsible for the things that they should have done.

Serious breaches of health and safety legislation on your construction project could result in construction work being stopped by HSE or your local authority and additional work may be needed to put things right. In the most serious circumstances, you could be prosecuted.

Fee for Intervention

HSE now recovers the costs of time spent dealing with material breaches of health and safety law. This is known as Fee for Intervention (FFI). FFI applies when an inspector finds something wrong that they believe is serious enough for them to write to you about. A fee is charged for the time spent by the inspector in sorting it out. Following the simple guidance in this leaflet may help you to avoid having to pay a fee.

Further reading

CONIAC industry guides http://www.citb.co.uk/health-safety-and-other-topics/health-safety/construction-design-and-management-regulations/cdm-guidance-documents/

Construction phase plan (CDM 2015): What you need to know as a busy builder Construction Information Sheet CIS80 HSE Books 2015 www.hse.gov.uk/pubns/cis80.htm

Health and safety in construction HSG150 (Third edition) HSE Books 2006 ISBN 978 0 7176 6182 4 www.hse.gov.uk/pubns/books/hsg150.htm

Managing health and safety in construction. Construction (Design and Management) Regulations 2015. Guidance on regulations L153 HSE Books 2015 ISBN 978 0 7176 6626 3 www.hse.gov.uk/pubns/books/l153.htm

Provision of welfare facilities during construction work Construction Information Sheet CIS59 HSE Books 2010 www.hse.gov.uk/pubns/cis59.htm

Workplace health, safety and welfare. Workplace (Health, Safety and Welfare) Regulations 1992. Approved Code of Practice and guidance L24 (Second edition) HSE Books 2013 ISBN 978 0 7176 6583 9 www.hse.gov.uk/pubns/books/l24.htm

Contains public sector information published by the Health and Safety Executive and licensed under the Open Government Licence